Tapinsert（Press-In Inserts）
This insert nut is slighly striked by handle pressing machine or hammer, which make it more suitable for quick mounting. Beside that,this part also have a high efficiency of strength, by using bolt-screwing technology,
| Major Insertion Methods | Press-In Inserts（insert by using handpress machine） |
| Material | Brass（Ｃ３６０４） |
| Plastic | Thermoplastics （thermoset plastics for some situation） |
■ Features
・Easily mounting
・Suitable for any kind of complicated work
・Special tool unnecessary
・Full compliance with RoHS Directive
・Suitable for any kind of complicated work
・Special tool unnecessary
・Full compliance with RoHS Directive
■ Dimensions
| Dimensional Drawing |
|
| Part Number | Thread and Pitch | A | B | C | Pilot Hole Dimension on Plastic (Reference) | |
| TS3.7-M2-4.0 | M2×0.4 | 3.71 | 4.00 | （3.10） | φ3.2 | ※ |
| TS4.5-M2.5-5.8 | M2.5×0.45 | 4.50 | 5.80 | （3.90） | φ4.0 | ※ |
| TS4.5-M3-5.8 | M3×0.5 | 4.50 | 5.80 | （3.90） | φ4.0 | ※ |
| TS6.2-M4-8.2 | M4×0.7 | 6.15 | 8.20 | （5.50） | φ5.6 | ※ |
| TS6.9-M5-9.5 | M5×0.8 | 6.90 | 9.50 | （6.30） | φ6.4 | ※ |
| TS8.5-M6-12.7 | M6×1.0 | 8.51 | 12.70 | （7.90） | φ8.0 | ※ |
※Standard Parts ・ Unit：mm
■ Tapsert Performance data (Reference)
| Part Number | ABS | |
| Pull-out （N） | Torque-out（N・m） | |
| TS3.7-M2-4.0 | 658 | 0.87 |
| TS4.5-M2.5-5.8 | 1,030 | 1.57 |
| TS4.5-M3-5.8 | 1,021 | 2.18 |
| TS6.2-M4-8.2 | 1,814 | 4.98 |
| TS6.9-M5-9.5 | 2,215 | 8.31 |
| TS8.5-M6-12.7 | 1,928 | 17.58 |
※The data above are experimental results obtained by Micro Fasteners. They are not a guarantee of the strength of our products.
1N≒0.098kgf 1N-m≒9.8kgf-cm
1N≒0.098kgf 1N-m≒9.8kgf-cm
■ NOTE
・ Please use the screw longer than the over-all length of insert （Dimension B）
・When inserts are tightened by screws, choose the screw length so that screws do not reach the bottom of insert pilot holes.
.When finish screw insert, please mount the torgue in order to screw Tapsert out.
・The diameter of the pilot hole for the mounting object should be smaller than the outer diameter of the insert (Dimension A).
・Products shape could have some difference due to part number.
・Be careful when using a Tapsert with a thermo-setting resin. threading the part will be tight, depending on the diameter of the pilot hole that is selected.
・ Pilot hole diameters are for reference only.
The diameter should be determined by testing before use.
・ Please contact us if you need Pb-free material for environmental reasons.
・ The specifications are subject to change without notice.
・ Please contact us if you have any other questions.
・When inserts are tightened by screws, choose the screw length so that screws do not reach the bottom of insert pilot holes.
.When finish screw insert, please mount the torgue in order to screw Tapsert out.
・The diameter of the pilot hole for the mounting object should be smaller than the outer diameter of the insert (Dimension A).
・Products shape could have some difference due to part number.
・Be careful when using a Tapsert with a thermo-setting resin. threading the part will be tight, depending on the diameter of the pilot hole that is selected.
・ Pilot hole diameters are for reference only.
The diameter should be determined by testing before use.
・ Please contact us if you need Pb-free material for environmental reasons.
・ The specifications are subject to change without notice.
・ Please contact us if you have any other questions.